L_PulleyTypeTab

Column Name

Description

Data Type

Length

Allow Nulls

Default

PUT_RID

ID-No. of the pulley group
(same diameter, but different number of grooves have same PUT_RID, see L_PulleyDimTab)
(ID-No.=RID number of the pulley type)
consecutive number

Integer

4

0
​

PUT_BASE_ID

Same built pulleys get the same BASE_ID. This is linked to the respective gear in the L_GearArtTab.

Integer

4

✓

0
​

PUT_DESC

Description of the pulley

VarWChar

150

✓

PUT_SUB_DESC

Sub-description of the pulley

VarWChar

150

✓

PUT_D

Central diameter (diameter of the reeving)

Double

9

✓

0
​

PUT_DI

Inside diameter of the pulley

Double

9

✓

0
​

PUT_DA

Outside diameter (if unknown, insert 0 for this value!)

Double

9

✓

0
​

PUT_D1_SHAFT

Shaft diameter 1

Double

9

✓

0
​

PUT_D2_SHAFT

Shaft diameter 2 (shaft diameter 2 = shaft diameter 1, if the shaft isn’t shaped tapered)

Double

9

✓

0
​

PUT_MF_RID

ID-No. of the manufacturer
​ID-No.=RID number of the manufacturer (MF_RID)

Integer

4

✓

0
​

PUT_T

Quantity of the parts of the pulley:

1 = one piece

2 = two pieces

SmallInt

2

✓

0
​

PUT_GROOVE_GAMMA_DEF

Vee groove angle gamma

Double

9

✓

0
​

PUT_GROOVE_TYPE

Groove type:

1 = vee groove

2 = vee groove with undercut

4 = seating groove

8 = seating groove with undercut

Integer

4

✓

0
​

PUT_GROOVE_TYPE_POSSIBLE

Possible groove forms (bit-linking, this means addition of the corresponding numbers).

For example:
Vee groove, vee groove with undercut, seating groove possible: 1+2+4=7, insert a 7.
​
1= vee groove

2= vee groove with undercut

4= seating groove

8= seating groove with undercut

Integer

4

✓

0
​

PUT_WEIGTH

Weight of the pulley (in kg)

Double

9

✓

0
​

PUT_TYPE

Type of the pulley:

0 = drive sheave

1 = deflection sheave/pulley

SmallInt

2

✓

0
​

PUT_MODE

pmSwapRopeDirection = 0x1:

For asymetric rope profiles, turn the rope leaving this pulley around by 180 degrees

pmSwapRopeWrap = 0x2:

Wrap the rope around this pulley the other way round (not supported for all pulley configurations; FOR INTERNAL USE ONLY right now, needs to be replaced with something that's more specific than 'do the other thing')

pmDoNotDrawDefault = 0x4:

If set, the default hardcoded pulley geometry is not drawn.

pmDoNotDrawCenterLines = 0x8:

If set, the center line crosshairs are not drawn.

pmDoubleWrap= 0x10 (decimal 16):

This is a double wrap pulley. Note that gearmode |= gmDoubleWrap must be set additionally

Integer

4

✓

0
​

PUT_ROPE_D_MIN

Minimum rope diameter

Double

9

✓

0
​

PUT_ROPE_D_DEF

Average rope diameter

Double

9

✓

0
​

PUT_ROPE_D_MAX

Maximum rope diameter

Double

9

✓

0
​

PUT_ROPE_D_TEXT

Text variable for rope mins and maxs

VarWChar

10

✓

PUT_PART_NO

Number of the supplier, part number or ordering number

VarWChar

50

✓