Skip to main content

The Elevator Editor at a Glance

What you see in the elevator editor: toolbar, configurator columns, sections and the BIM model.

Written by Sabine Bunese

The elevator editor opens when you open an elevator group. It shows each elevator as a column of values on the left and as a live drawing on the right. The drawing is redrawn every time you change a value.

What you see

  1. Breadcrumb: at the top, with the elevator group chip on the right. Use it to go back to the building or site.

  2. Toolbar: below the breadcrumb.

    • Focus graphic gives the drawing more room.

    • The two arrow buttons expand or collapse all sections at once.

    • −, 100% and + zoom the configurator columns.

  3. Catalog badge: on the far right, it names the catalog in use. CHANGE CATALOG beside it lets you pick another one.

  4. Configurator columns: one column per elevator, headed with the elevator's name. You can click the name to rename the elevator.

  5. BIM MODEL panel: the sheet list on the left and the drawing in the middle.

The sections

Each elevator column is a stack of sections. Each section shows its current value on the right and unfolds when you click it.

Section

What it covers

REQUIREMENTS

The filters that decide which catalog models are offered

MODEL

The model family in use

PAYLOAD

Rated load and number of persons

CABIN

Car width, depth and height

COUNTERWEIGHT

Counterweight position

ENTRANCES

Entrance availability, Door width and height, opening type and pocket availability

DOOR FRONT

The door front design

SHAFT

Shaft width and depth, reduced head and pit availability

STOPS

Number of stops and entrances activation

The sections are search criteria

The values you set are search criteria, not fixed values. In CABIN, for example, you ask for a minimum and maximum car width and depth, a proportion, a car height and access requirements such as wheelchair or bed. EAO then picks the catalog model that fits. The line above the section tells you what the chosen model actually delivers.

REQUIREMENTS shows where each filter comes from: the site, the building, the elevator group and the model. Switching a filter off widens the search.

If you change the catalog and the new catalog can't meet all your requirements, the elevator group is put ON HOLD. A red banner shows how many elevators are affected. EAO doesn't generate 2D, 3D, BIM or export for the group until the marked issue is resolved.

Groups with several elevators

An elevator group can hold up to eight elevators. They stand side by side in a bank and are planned together. In the editor, their columns are shown next to each other under BANK 1.

The columns open and close together: when you unfold a section in one elevator, the same section unfolds in all the others. That way you can compare the elevators directly.

Two banks facing each other

You can split the elevators of a group into two banks that face each other across a hall. Click the gear icon next to BANK 1. The Elevator bank settings open:

Setting

What it does

Split into 2 Banks

Turns the second bank on or off.

Split behind

The elevator after which the second bank starts.

Across the hall distance (mm)

The distance between the two banks, across the hall.

Align Bank 1 and Bank 2

The side on which the two banks line up, for example Left.

Offset (mm)

How far the second bank is shifted sideways from the first.

Click Apply to use the settings.

The editor then shows BANK 1 and BANK 2, each with its own gear icon and an Add elevator button. The 2D plan shows both banks facing each other, with the hall distance and the offset as dimensions.

Catalog or special dimensions

Each elevator has a Catalog and a Special button next to its name.

  • Catalog (default): all values come from the catalog.

  • Special: lets you change dimensions beyond the catalog. An elevator group with special dimensions shows a SPECIAL badge on its card.

The BIM model

The BIM MODEL panel shows the elevator as it stands. Live preview in the title means the drawing is updated as you work.

  • SHEETS lists seven drawings: three BIM models (LOD 100–300), three 2D drawings (plan, verticals, details) and the VT concept layout. Type in Filter sheets… to find one quickly.

  • Above the drawing, the hand button lets you drag the sheet, and the arrow button lets you pick a dimension. −, 100% and + zoom, and Fit brings the whole sheet back into view.

  • Pick mode only works for elevators set to Special. Click a dimension in the drawing, for example the shaft width. A window opens that shows how the value is made up: for the shaft width, the left clearance, counterweight package, car platform and right clearance. You can change the clearances there and click Apply.

  • Export at the top right downloads the current sheet as DWG or PDF. See Export a Drawing as DWG or PDF.

Did this answer your question?